My XSL knowledge is minimal, but if for example I'm using bourne as the language, do I need to import something specific to bourne? The README has a note about importing, but it isn't clear what the intended import file is.
On 2/11/2017 12:42 PM, stimits@comcast.net wrote:
> Hi,
>
> From the link on Saxon plus other information I put together the
> simplest test case (which sort of works). The command is essentially
> this (other commands validate the XML with jing and xmllint before
> calling Saxon):
> CLASSPATH=${CLASSPATH};\
> java \
> -Dxslthl.config=${XSLTHL}/highlighters/xslthl-config.xml \
> com.icl.saxon.StyleSheet \
> -o ${OBJ}/${TITLE}_monolithic.fo \
> ${OBJ}/${TITLE}_monolithic.xml \
> ${XSLT}/fo/docbook.xsl \
> use.extensions=1
>
> This does enable line numbering in programlisting tags, and options
> related to numbering do as expected. However, in attempting to get the
> syntax highlighting to work (see
> http://www.sagehill.net/docbookxsl/SyntaxHighlighting.html) nothing I've
> tried has any effect (test cases were with "bourne" and "ini" files).
>
> The CLASSPATH contains the following files, and no error occurs (for the
> sake of brevity I'm showing only the relative paths, but the full path
> is used without error in the actual Makefile):
> docbook-xsl-ns-1.79.1/tools/lib/*saxon.jar*:docbook5/stylesheet/docbook-xsl-ns-1.79.1/extensions/*saxon65.jar*:xml/xslthl-2.1.3/*xslthl-2.1.3.jar*
>
> Since I get no errors, and because the Saxon processing is otherwise
> working, is there any additional requirement to keep syntax highlighting
> from failing as if the option did not exist? Is syntax highlighting
> something which maybe requires the Xalan parser? Is there perhaps
> something from param.xsl which needs to change and not mentioned in the
> above URL on syntax highlighting?
>
> Thanks!
>
> ----- Original Message -----
> From: Richard Hamilton <hamilton@xmlpress.net>
> To: stimits@comcast.net
> Cc: Docbook <docbook-apps@lists.oasis-open.org>
> Sent: Sat, 11 Feb 2017 00:50:21 -0000 (UTC)
> Subject: Re: [docbook-apps] <programlisting linenumbering="numbered">
> does not number...
> Hi,
> Here is the link to the part of Bob’s book that covers the Saxon processor:
> http://sagehill.net/docbookxsl/InstallingAProcessor.html#InstallSaxon
> I think you can keep the xmllint processing as is (I use it for XInclude
> processing, too), and just swap in saxon for xsltproc, using Bob’s
> instructions.
> I don’t bother swapping in Xerces (I don’t use any of the features that
> go beyond what Saxon supports).
> Best regards,
> Dick
> -------
> XML Press
> XML for Technical Communicators
> http://xmlpress.net
> hamilton@xmlpress.net
>> On Feb 10, 2017, at 12:26, stimits@comcast.net wrote:
>>
>> Hi,
>>
>> I was going by this reference as to requirements, and have not read
> the whole book (thus I did not yet see the Java requirement):
>> http://tdg.docbook.org/tdg/5.1/programlisting.html
>>
>> Admittedly I'm trying to do something quicker than I should and not
> reading everything (I've been through a lot of material, but it's just a
> drop in the bucket for everything needed when I really just need to sit
> down and write content). I've had some frustrations getting the
> Java-based processors working and have tried to stick to the
> xmllint/jing/xsltproc family for that single reason. The Java-based
> processing answer likely also answers my earlier syntax highlighting
> question about whether to abandon my current approach with xmllint.
>>
>> To use Saxon or Xalan I would have to change the current build scheme,
> which I've never succeeded at:
>> xmllint --output "${OBJ}/${TITLE}_monolithic.xml" --nonet --noent
> -xinclude "${CONTENT}/${TITLE}.xml"
>> xsltproc --output ${OBJ}/${TITLE}_monolithic.fo ${XSLT}/docbook.xsl
> ${OBJ}/${TITLE}_monolithic.xml
>> fop -c ${PREFIX}/fop.xconf -fo ${OBJ}/${TITLE}_monolithic.fo -pdf
> ${OUT}/${TITLE}.pdf
>>
>> I realize I'm probably asking a lot, but is there any advice I can get
> on editing that chain of commands to instead work with Saxon or Xalan?
> Getting past the tools on the command line (for a hand written Makefile)
> is just getting frustrating and is why the current chain of commands
> have never evolved to anything Java-based.
>>
>> I do plan on reading more (I'm not resisting reading), but there are
> other requirements which tend to require at least a draft to be
> available sooner rather than later.
>>
>> Thanks!
>>
>> ----- Original Message -----
>> From: Bob Stayton <bobs@sagehill.net>
>> To: stimits@comcast.net, Docbook <docbook-apps@lists.oasis-open.org>
>> Sent: Fri, 10 Feb 2017 19:09:00 -0000 (UTC)
>> Subject: Re: [docbook-apps] <programlisting linenumbering="numbered">
> does not number...
>> Hi,
>> Did you read this section in my online book about line numbering? It
>> only works with Java-based processors.
>> Bob Stayton
>> Sagehill Enterprises
>> bobs@sagehill.net
>> On 2/10/2017 11:01 AM, stimits@comcast.net wrote:
>> > Hi,
>> >
>> > Under DocBook 5.1 I've been able to list programs, but line numbering
>> > has no effect (and there is no error under xmllint or jing). Is there
>> > some ENTITY or other precondition required for line numbering under 5.1?
>> >
>> > Thanks!