OASIS Mailing List ArchivesView the OASIS mailing list archive below
or browse/search using MarkMail.

 


Help: OASIS Mailing Lists Help | MarkMail Help

virtio-comment message

[Date Prev] | [Thread Prev] | [Thread Next] | [Date Next] -- [Date Index] | [Thread Index] | [List Home]


Subject: [PATCH v6] Add virtio SCMI device specification


This patch proposes a new virtio device for the Arm SCMI protocol.

The device provides a simple transport for the Arm SCMI protocol[1]. The
*S*ystem *C*ontrol and *M*anagement *I*nterface protocol allows speaking
to system controllers that allow orchestrating things like power
management, system state management and sensor access. The SCMI protocol
is used on SoCs where multiple cores and co-processors need access to
these resources.

The virtio transport allows making use of this protocol in virtualized
systems.

[1] https://developer.arm.com/docs/den0056/c

Signed-off-by: Peter Hilber <peter.hilber@opensynergy.com>
---

Notes:

    Since sending out v5 in May 2020, there has been no additional
    feedback w.r.t. the spec. An RfC patch series for the driver is now
    available at [1]. OpenSynergy also has a proprietary implementation
    of the device (without the VIRTIO_SCMI_F_SHARED_MEMORY feature so
    far).

    So I would like to request a vote on adding the device in a few weeks.
    
    The PDF output is available at [2].
    
    [1] https://lore.kernel.org/linux-arm-kernel/20201105212116.411422-1-peter.hilber@opensynergy.com/
    [2] https://share.mailbox.org/ajax/share/056076e70571144f50c4ca7571144b319a1d7236dda1cd3b/1/8/MzQ/MzQvMQ

    Changes for v6:

    - Refer to new SCMI spec version 3.0 (DEN0056C), which has a
      provision for SHM race conditions.

    - Resolve conflicts with other added device documentation.

    Changes for v5:
    
    - Remove requirements on shared memory added in v4, since an upcoming
    new version of the Arm SCMI spec[1] will provide a generic, more
    powerful way to handle concurrent access to shared memory.
    
    Changes for v4:
    
    - Add more requirements on shared memory regions after feedback from
      Alex BennÃe.
    
    Changes for v3:
    
    - Add tentative device ID 32 in device section.
    
    - Remove redundant 'len' fields. The length of the payload fields can
      already be deduced from the generic virtqueue 'len' fields. Therefore,
      remove the redundant device-specific 'len' fields.
    
    - Reword requirement that driver must not put too small buffers into
      eventq.
    
    Changes for v2:
    
    - CC virtio-dev list.
    - Define size of erroneous delayed/not delayed responses.
    - Use correct long name for SCMI.
    - Remove restriction to `embedded' in commit message.
    - Add motivation for conceptual per-message-channels.
    - Device may now just drop notification if no buffers are available.
    

 conformance.tex  |  34 ++++--
 content.tex      |   1 +
 introduction.tex |   3 +
 virtio-scmi.tex  | 271 +++++++++++++++++++++++++++++++++++++++++++++++
 4 files changed, 303 insertions(+), 6 deletions(-)
 create mode 100644 virtio-scmi.tex

diff --git a/conformance.tex b/conformance.tex
index 17c390d..a164cbb 100644
--- a/conformance.tex
+++ b/conformance.tex
@@ -27,9 +27,10 @@ \section{Conformance Targets}\label{sec:Conformance / Conformance Targets}
 \ref{sec:Conformance / Driver Conformance / Socket Driver Conformance},
 \ref{sec:Conformance / Driver Conformance / RPMB Driver Conformance},
 \ref{sec:Conformance / Driver Conformance / IOMMU Driver Conformance},
-\ref{sec:Conformance / Driver Conformance / Sound Driver Conformance}
-\ref{sec:Conformance / Driver Conformance / Memory Driver Conformance} or
-\ref{sec:Conformance / Driver Conformance / I2C Adapter Driver Conformance}.
+\ref{sec:Conformance / Driver Conformance / Sound Driver Conformance},
+\ref{sec:Conformance / Driver Conformance / Memory Driver Conformance},
+\ref{sec:Conformance / Driver Conformance / I2C Adapter Driver Conformance} or
+\ref{sec:Conformance / Driver Conformance / SCMI Driver Conformance}.
 
     \item Clause \ref{sec:Conformance / Legacy Interface: Transitional Device and Transitional Driver Conformance}.
   \end{itemize}
@@ -49,9 +50,10 @@ \section{Conformance Targets}\label{sec:Conformance / Conformance Targets}
 \ref{sec:Conformance / Device Conformance / Socket Device Conformance}, 
 \ref{sec:Conformance / Device Conformance / RPMB Device Conformance},
 \ref{sec:Conformance / Device Conformance / IOMMU Device Conformance},
-\ref{sec:Conformance / Device Conformance / Sound Device Conformance}
-\ref{sec:Conformance / Device Conformance / Memory Device Conformance} or
-\ref{sec:Conformance / Device Conformance / I2C Adapter Device Conformance}.
+\ref{sec:Conformance / Device Conformance / Sound Device Conformance},
+\ref{sec:Conformance / Device Conformance / Memory Device Conformance},
+\ref{sec:Conformance / Device Conformance / I2C Adapter Device Conformance} or
+\ref{sec:Conformance / Device Conformance / SCMI Device Conformance}.
 
     \item Clause \ref{sec:Conformance / Legacy Interface: Transitional Device and Transitional Driver Conformance}.
   \end{itemize}
@@ -277,6 +279,15 @@ \section{Conformance Targets}\label{sec:Conformance / Conformance Targets}
 \item \ref{drivernormative:Device Types / I2C Adapter Device / Device Operation}
 \end{itemize}
 
+\conformance{\subsection}{SCMI Driver Conformance}\label{sec:Conformance / Driver Conformance / SCMI Driver Conformance}
+
+An SCMI driver MUST conform to the following normative statements:
+
+\begin{itemize}
+\item \ref{drivernormative:Device Types / SCMI Device / Device Operation / cmdq Operation}
+\item \ref{drivernormative:Device Types / SCMI Device / Device Operation / Setting Up eventq Buffers}
+\end{itemize}
+
 \conformance{\section}{Device Conformance}\label{sec:Conformance / Device Conformance}
 
 A device MUST conform to the following normative statements:
@@ -505,6 +516,17 @@ \section{Conformance Targets}\label{sec:Conformance / Conformance Targets}
 \item \ref{devicenormative:Device Types / I2C Adapter Device / Device Operation}
 \end{itemize}
 
+\conformance{\subsection}{SCMI Device Conformance}\label{sec:Conformance / Device Conformance / SCMI Device Conformance}
+
+An SCMI device MUST conform to the following normative statements:
+
+\begin{itemize}
+\item \ref{devicenormative:Device Types / SCMI Device / Feature bits}
+\item \ref{devicenormative:Device Types / SCMI Device / Device Operation / cmdq Operation}
+\item \ref{devicenormative:Device Types / SCMI Device / Device Operation / eventq Operation}
+\item \ref{devicenormative:Device Types / SCMI Device / Device Operation / Shared Memory Operation}
+\end{itemize}
+
 \conformance{\section}{Legacy Interface: Transitional Device and Transitional Driver Conformance}\label{sec:Conformance / Legacy Interface: Transitional Device and Transitional Driver Conformance}
 A conformant implementation MUST be either transitional or
 non-transitional, see \ref{intro:Legacy
diff --git a/content.tex b/content.tex
index 835f1ea..40ab30a 100644
--- a/content.tex
+++ b/content.tex
@@ -6532,6 +6532,7 @@ \subsubsection{Legacy Interface: Framing Requirements}\label{sec:Device
 \input{virtio-sound.tex}
 \input{virtio-mem.tex}
 \input{virtio-i2c.tex}
+\input{virtio-scmi.tex}
 
 \chapter{Reserved Feature Bits}\label{sec:Reserved Feature Bits}
 
diff --git a/introduction.tex b/introduction.tex
index bc0217f..7204b24 100644
--- a/introduction.tex
+++ b/introduction.tex
@@ -76,6 +76,9 @@ \section{Normative References}\label{sec:Normative References}
 	\phantomsection\label{intro:I2C}\textbf{[I2C]} &
 	I2C-bus specification and user manual,
 	\newline\url{https://www.nxp.com/docs/en/user-guide/UM10204.pdf}\\
+	\phantomsection\label{intro:SCMI}\textbf{[SCMI]} &
+	Arm System Control and Management Interface, DEN0056,
+	\newline\url{https://developer.arm.com/docs/den0056/c}, version C and any future revisions\\
 
 \end{longtable}
 
diff --git a/virtio-scmi.tex b/virtio-scmi.tex
new file mode 100644
index 0000000..c4b8dd0
--- /dev/null
+++ b/virtio-scmi.tex
@@ -0,0 +1,271 @@
+\section{SCMI Device}\label{sec:Device Types / SCMI Device}
+
+An SCMI device implements the Arm System Control and Management
+Interface (SCMI). SCMI can be used for sensors, power state management,
+clock management and performance management among other things.
+
+This section relies on definitions from the \hyperref[intro:SCMI]{SCMI
+specification}.
+
+Virtio SCMI device and driver are mapped to SCMI platform and agent
+respectively. The device is visible to a particular SCMI agent. The
+device allows a guest to communicate as an SCMI agent using one or more
+SCMI protocols. The default SCMI protocols are defined in the
+\hyperref[intro:SCMI]{SCMI specification}. Virtio provides a transport
+medium for exchanging SCMI messages between the SCMI agent and platform.
+The virtio SCMI transport allows the queueing of multiple messages and
+responses.
+
+SCMI FastChannels are not supported.
+
+\subsection{Device ID}\label{sec:Device Types / SCMI Device / Device ID}
+
+32
+
+\subsection{Virtqueues}\label{sec:Device Types / SCMI Device / Virtqueues}
+
+\begin{description}
+\item[0] cmdq
+\item[1] eventq
+\end{description}
+
+The cmdq is used by the driver to send commands to the device. The
+device replies with responses (not delayed responses) over the cmdq.
+
+The eventq is used by the device to send notifications and delayed
+responses. The eventq only exists if VIRTIO_SCMI_F_P2A_CHANNELS was
+negotiated.
+
+\subsection{Feature bits}\label{sec:Device Types / SCMI Device / Feature bits}
+
+\begin{description}
+\item[VIRTIO_SCMI_F_P2A_CHANNELS (0)] Device implements some SCMI
+notifications, or delayed responses.
+\item[VIRTIO_SCMI_F_SHARED_MEMORY (1)] Device implements any SCMI
+statistics shared memory region.
+\end{description}
+
+VIRTIO_SCMI_F_P2A_CHANNELS is used to determine the existence of the
+eventq. The eventq is required for SCMI notifications and delayed
+responses.
+
+VIRTIO_SCMI_F_SHARED_MEMORY is used to determine whether the device
+provides any SCMI statistics shared memory region. SCMI statistics
+shared memory regions are defined by some SCMI protocols.
+
+The SCMI protocols provide the PROTOCOL_MESSAGE_ATTRIBUTES commands to
+inquire about the particular SCMI notifications and delayed responses
+implemented by the device. The SCMI protocols provide additional
+commands to detect other features implemented by the device.
+
+\devicenormative{\subsubsection}{Feature bits}{Device Types / SCMI Device / Feature bits}
+
+The device MUST offer VIRTIO_SCMI_F_P2A_CHANNELS if the device can
+implement at least one SCMI notification, or delayed response.
+
+The device MUST offer VIRTIO_SCMI_F_SHARED_MEMORY if the device can
+implement at least one SCMI statistics shared memory region.
+
+\subsection{Device configuration layout}\label{sec:Device Types / SCMI Device / Device configuration layout}
+
+There is no configuration data for the device.
+
+\subsection{Device Initialization}\label{sec:Device Types / SCMI Device / Device Initialization}
+
+The
+\hyperref[sec:General Initialization And Device Operation / Device Initialization]{general
+requirements on device initialization} apply.
+
+\subsection{Device Operation}\label{sec:Device Types / SCMI Device / Device Operation}
+
+The SCMI transport used for the device puts each SCMI message into a
+dedicated virtio buffer. The driver uses the cmdq for transmitting SCMI
+commands and receiving the corresponding SCMI responses. The device uses
+the eventq for transmitting SCMI notifications and delayed responses.
+Each message includes an SCMI protocol header and payload, as defined by
+the \hyperref[intro:SCMI]{SCMI specification}.
+
+\subsubsection{cmdq Operation}\label{sec:Device Types / SCMI Device / Device Operation / cmdq Operation}
+
+Each buffer in the cmdq holds a single SCMI command once the buffer has
+been made available. When the buffer has been marked as used, it
+contains the SCMI response. An arbitrary number of such SCMI messages
+can be in transit at the same time. Conceptually, each SCMI message in
+the cmdq uses its own SCMI A2P (agent to platform) channel.
+
+The SCMI response is in the same virtio buffer as the corresponding SCMI
+command. The response contains the return values which SCMI specifies
+for each command, whether synchronous or asynchronous. Delayed responses
+are distinct SCMI messages transmitted over the eventq.
+
+Buffers in the cmdq contain both the request and the response. A request
+has the following layout:
+
+\begin{lstlisting}
+struct virtio_scmi_request {
+        le32 hdr;
+        u8 params[<actual parameters size>];
+};
+\end{lstlisting}
+
+The virtio_scmi_request fields are interpreted as follows:
+
+\begin{description}
+\item[\field{hdr}] (device-readable) contains the SCMI message header
+\item[\field{params}] (device-readable) comprises the SCMI message
+parameters
+\end{description}
+
+A cmdq response has the following layout:
+
+\begin{lstlisting}
+struct virtio_scmi_response {
+        le32 hdr;
+        u8 ret_values[<actual return values size>];
+};
+\end{lstlisting}
+
+The virtio_scmi_response fields are interpreted as follows:
+
+\begin{description}
+\item[\field{hdr}] (device-writable) contains the SCMI message header
+\item[\field{ret_values}] (device-writable) comprises the SCMI message
+return values
+\end{description}
+
+If VIRTIO_SCMI_F_P2A_CHANNELS was not negotiated, the device responds to
+SCMI commands as if no SCMI notifications or delayed responses were
+implemented.
+
+\devicenormative{\paragraph}{cmdq Operation}{Device Types / SCMI Device / Device Operation / cmdq Operation}
+
+The device MAY process available commands out of order and in parallel.
+
+The device MUST process all available commands eventually, even in the
+case of bursts of multiple command messages.
+
+If the \field{status} field in the \field{virtio_scmi_response}
+\field{ret_values} has a value other than SUCCESS, the device MUST set
+the size of \field{ret_values} to the size of the \field{status} field.
+
+If the driver requests an SCMI notification or a delayed response and
+there are currently NOT enough available buffers in the eventq, the
+device SHOULD still return SCMI status code SUCCESS.
+
+If VIRTIO_SCMI_F_P2A_CHANNELS was not negotiated, the device MUST deny
+any request for an SCMI notification or a delayed response by returning
+SCMI status code NOT_SUPPORTED.
+
+If VIRTIO_SCMI_F_P2A_CHANNELS was not negotiated, the device MUST NOT
+indicate in the PROTOCOL_MESSAGE_ATTRIBUTES return values that any SCMI
+notification, or delayed response, is implemented.
+
+\drivernormative{\paragraph}{cmdq Operation}{Device Types / SCMI Device / Device Operation / cmdq Operation}
+
+Before sending a command, the driver MUST wait for responses to all
+commands whose completion the driver considers prerequisites to
+executing the command.
+
+With every command message, the driver MUST provide enough
+device-writable memory to enable the device to return corresponding
+return values.
+
+If VIRTIO_SCMI_F_P2A_CHANNELS was not negotiated, the driver MUST NOT
+request any SCMI notification, nor any delayed response.
+
+\subsubsection{Setting Up eventq Buffers}
+
+The driver has to populate the eventq before the device can use it.
+
+\drivernormative{\paragraph}{Setting Up eventq Buffers}{Device Types / SCMI Device / Device Operation / Setting Up eventq Buffers}
+
+If VIRTIO_SCMI_F_P2A_CHANNELS was negotiated, the driver SHOULD populate
+the eventq with buffers.
+
+The driver MUST NOT put device-readable descriptors into the eventq.
+
+The driver MUST NOT put into the eventq any buffer which is smaller than
+the largest SCMI P2A (platform to agent) message which the driver will
+request.
+
+\subsubsection{eventq Operation}
+
+Each buffer in the eventq holds (once the buffer is marked as used)
+either a single SCMI notification, or a single SCMI delayed response. An
+arbitrary number of such SCMI messages can be in transit at the same
+time. Conceptually, each SCMI message transmitted over the eventq uses
+its own SCMI P2A (platform to agent) channel. Buffers in the eventq have
+the following layout:
+
+\begin{lstlisting}
+struct virtio_scmi_event_msg {
+        /* start of device-writable data */
+        le32 hdr;
+        u8 payload[<actual payload size>];
+};
+\end{lstlisting}
+
+\begin{description}
+\item[\field{hdr}] (device-writable) contains the SCMI message header
+\item[\field{payload}] (device-writable) comprises the SCMI message
+payload
+\end{description}
+
+\devicenormative{\paragraph}{eventq Operation}{Device Types / SCMI Device / Device Operation / eventq Operation}
+
+If the device intends to send a notification and there are no available
+buffers in the eventq, the device MAY drop the notification, or send a
+corresponding notification later, once enough buffers become available.
+
+The device MAY send the notification later if the events which cause the
+notification take place in quick succession.
+
+If the device sends the notification later, the device MAY send the
+notification with updated data, unless the specific SCMI protocol
+disallows this.
+
+If the device intends to send a notification and there are available
+buffers, but one of the buffers is too small to fit the notification,
+the device MAY omit the notification.
+
+If the device intends to send a delayed response and there are no
+available buffers in the eventq, the device MUST send the corresponding
+delayed response once enough buffers become available.
+
+If the \field{status} field in a delayed response \field{payload} has a
+value other than SUCCESS, the device MUST set the size of
+\field{payload} to the size of the \field{status} field.
+
+\subsubsection{Shared Memory Operation}
+
+Various SCMI protocols define statistics shared memory regions (for
+statistics and sensor values).
+
+\devicenormative{\paragraph}{Shared Memory Operation}{Device Types / SCMI Device / Device Operation / Shared Memory Operation}
+
+If VIRTIO_SCMI_F_SHARED_MEMORY was negotiated, the device MAY implement
+an SCMI statistics shared memory region using a virtio shared memory
+region.
+
+If the device implements a shared memory region, the device MUST assign
+the corresponding shmid as per the following table:
+
+\begin{tabular}{|l|l|}
+\hline
+SCMI statistics shared memory region & Virtio shmid \\
+\hline \hline
+Reserved (invalid) & 0 \\
+\hline
+Power state statistics shared memory region & 1 \\
+\hline
+Performance domain statistics shared memory region & 2 \\
+\hline
+Sensor Values Shared Memory & 3 \\
+\hline
+Reserved for future use & 4 to 0x7F \\
+\hline
+Vendor-specific statistics shared memory regions & 0x80 to 0xFF \\
+\hline
+Reserved for future use & 0x100 and greater \\
+\hline
+\end{tabular}

base-commit: f5fd3fca7e4006108b3f9ba91c0b76c5eb6c0726
-- 
2.25.1




[Date Prev] | [Thread Prev] | [Thread Next] | [Date Next] -- [Date Index] | [Thread Index] | [List Home]