[Date Prev] | [Thread Prev] | [Thread Next] | [Date Next] -- [Date Index] | [Thread Index] | [List Home]
Subject: Re: [PATCH v5 2/2] virtio-net: use mtu size as buffer length for big packets
On Thu, Sep 22, 2022 at 10:04:53AM +0000, Parav Pandit wrote:
>
> > From: Michael S. Tsirkin <mst@redhat.com>
> > Sent: Thursday, September 22, 2022 5:35 AM
> >
> > On Thu, Sep 01, 2022 at 05:10:38AM +0300, Gavin Li wrote:
> > > Currently add_recvbuf_big() allocates MAX_SKB_FRAGS segments for big
> > > packets even when GUEST_* offloads are not present on the device.
> > > However, if guest GSO is not supported, it would be sufficient to
> > > allocate segments to cover just up the MTU size and no further.
> > > Allocating the maximum amount of segments results in a large waste of
> > > buffer space in the queue, which limits the number of packets that can
> > > be buffered and can result in reduced performance.
> > >
> > > Therefore, if guest GSO is not supported, use the MTU to calculate the
> > > optimal amount of segments required.
> > >
> > > When guest offload is enabled at runtime, RQ already has packets of
> > > bytes less than 64K. So when packet of 64KB arrives, all the packets
> > > of such size will be dropped. and RQ is now not usable.
> > >
> > > So this means that during set_guest_offloads() phase, RQs have to be
> > > destroyed and recreated, which requires almost driver reload.
> > >
> > > If VIRTIO_NET_F_CTRL_GUEST_OFFLOADS has been negotiated, then it
> > > should always treat them as GSO enabled.
> > >
> > > Accordingly, for now the assumption is that if guest GSO has been
> > > negotiated then it has been enabled, even if it's actually been
> > > disabled at runtime through VIRTIO_NET_F_CTRL_GUEST_OFFLOADS.
> > >
> > > Below is the iperf TCP test results over a Mellanox NIC, using vDPA
> > > for
> > > 1 VQ, queue size 1024, before and after the change, with the iperf
> > > server running over the virtio-net interface.
> > >
> > > MTU(Bytes)/Bandwidth (Gbit/s)
> > > Before After
> > > 1500 22.5 22.4
> > > 9000 12.8 25.9
> > >
> > > Signed-off-by: Gavin Li <gavinl@nvidia.com>
> > > Reviewed-by: Gavi Teitz <gavi@nvidia.com>
> > > Reviewed-by: Parav Pandit <parav@nvidia.com>
> > > Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
> > > Reviewed-by: Si-Wei Liu <si-wei.liu@oracle.com>
> >
> > OK I think the logic is correct, it's just a bit harder to read than necessary.
> > Small improvement suggestions:
> >
> >
> > > ---
> > > changelog:
> > > v4->v5
> > > - Addressed comments from Michael S. Tsirkin
> > > - Improve commit message
> > > v3->v4
> > > - Addressed comments from Si-Wei
> > > - Rename big_packets_sg_num with big_packets_num_skbfrags
> > > v2->v3
> > > - Addressed comments from Si-Wei
> > > - Simplify the condition check to enable the optimization
> > > v1->v2
> > > - Addressed comments from Jason, Michael, Si-Wei.
> > > - Remove the flag of guest GSO support, set sg_num for big packets and
> > > use it directly
> > > - Recalculate sg_num for big packets in virtnet_set_guest_offloads
> > > - Replace the round up algorithm with DIV_ROUND_UP
> > > ---
> > > drivers/net/virtio_net.c | 37 ++++++++++++++++++++++++-------------
> > > 1 file changed, 24 insertions(+), 13 deletions(-)
> > >
> > > diff --git a/drivers/net/virtio_net.c b/drivers/net/virtio_net.c index
> > > f831a0290998..dbffd5f56fb8 100644
> > > --- a/drivers/net/virtio_net.c
> > > +++ b/drivers/net/virtio_net.c
> > > @@ -225,6 +225,9 @@ struct virtnet_info {
> > > /* I like... big packets and I cannot lie! */
> > > bool big_packets;
> > >
> > > + /* number of sg entries allocated for big packets */
> > > + unsigned int big_packets_num_skbfrags;
> > > +
> > > /* Host will merge rx buffers for big packets (shake it! shake it!) */
> > > bool mergeable_rx_bufs;
> > >
> >
> > big_packets_num_skbfrags -> big_packet_num_skbfrags
> >
> > > @@ -1331,10 +1334,10 @@ static int add_recvbuf_big(struct virtnet_info
> > *vi, struct receive_queue *rq,
> > > char *p;
> > > int i, err, offset;
> > >
> > > - sg_init_table(rq->sg, MAX_SKB_FRAGS + 2);
> > > + sg_init_table(rq->sg, vi->big_packets_num_skbfrags + 2);
> > >
> > > - /* page in rq->sg[MAX_SKB_FRAGS + 1] is list tail */
> > > - for (i = MAX_SKB_FRAGS + 1; i > 1; --i) {
> > > + /* page in rq->sg[vi->big_packets_num_skbfrags + 1] is list tail */
> > > + for (i = vi->big_packets_num_skbfrags + 1; i > 1; --i) {
> > > first = get_a_page(rq, gfp);
> > > if (!first) {
> > > if (list)
> > > @@ -1365,7 +1368,7 @@ static int add_recvbuf_big(struct virtnet_info
> > > *vi, struct receive_queue *rq,
> > >
> > > /* chain first in list head */
> > > first->private = (unsigned long)list;
> > > - err = virtqueue_add_inbuf(rq->vq, rq->sg, MAX_SKB_FRAGS + 2,
> > > + err = virtqueue_add_inbuf(rq->vq, rq->sg,
> > > +vi->big_packets_num_skbfrags + 2,
> > > first, gfp);
> > > if (err < 0)
> > > give_pages(rq, first);
> > > @@ -3690,13 +3693,27 @@ static bool virtnet_check_guest_gso(const
> > struct virtnet_info *vi)
> > > virtio_has_feature(vi->vdev, VIRTIO_NET_F_GUEST_UFO); }
> > >
> > > +static void virtnet_set_big_packets_fields(struct virtnet_info *vi,
> > > +const int mtu) {
> > > + bool guest_gso = virtnet_check_guest_gso(vi);
> > > +
> > > + /* If device can receive ANY guest GSO packets, regardless of mtu,
> > > + * allocate packets of maximum size, otherwise limit it to only
> > > + * mtu size worth only.
> > > + */
> > > + if (mtu > ETH_DATA_LEN || guest_gso) {
> > > + vi->big_packets = true;
> > > + vi->big_packets_num_skbfrags = guest_gso ?
> > MAX_SKB_FRAGS : DIV_ROUND_UP(mtu, PAGE_SIZE);
> > > + }
> > > +}
> > > +
> > > static int virtnet_probe(struct virtio_device *vdev) {
> > > int i, err = -ENOMEM;
> > > struct net_device *dev;
> > > struct virtnet_info *vi;
> > > u16 max_queue_pairs;
> > > - int mtu;
> > > + int mtu = 0;
> > >
> >
> > I think it's better to drop this and instead just put the code
> > where we already know the config. So:
> >
> > > /* Find if host supports multiqueue/rss virtio_net device */
> > > max_queue_pairs = 1;
> > > @@ -3784,10 +3801,6 @@ static int virtnet_probe(struct virtio_device
> > *vdev)
> > > INIT_WORK(&vi->config_work, virtnet_config_changed_work);
> > > spin_lock_init(&vi->refill_lock);
> > >
> > > - /* If we can receive ANY GSO packets, we must allocate large ones.
> > */
> > > - if (virtnet_check_guest_gso(vi))
> > > - vi->big_packets = true;
> > > -
> > > if (virtio_has_feature(vdev, VIRTIO_NET_F_MRG_RXBUF))
> > > vi->mergeable_rx_bufs = true;
> > >
> > > @@ -3853,12 +3866,10 @@ static int virtnet_probe(struct virtio_device
> > *vdev)
> > >
> > > dev->mtu = mtu;
> > > dev->max_mtu = mtu;
> > > -
> > > - /* TODO: size buffers correctly in this case. */
> > > - if (dev->mtu > ETH_DATA_LEN)
> > > - vi->big_packets = true;
> >
> > /* Size buffers to fit mtu. */
> > if (mtu > ETH_DATA_LEN) {
> > vi->big_packets = true;
> > vi->big_packets_num_skbfrags = DIV_ROUND_UP(mtu,
> > PAGE_SIZE);
> > }
> >
> How doing things twice is better i.e. when mtu is > ETH_DATA_LEN and gso is offered?
> It calculates big_packets variable twice.
>
> It also easier to read the code at single place where big_packets decision is taken.
I guess it depends on what you want to keep in one place.
I just wanted to reduce the testing burden on the submitter.
What I proposed makes the functional change minimal.
It's nitpicking to be frank. v6 arrived while I was traveling
and I didn't notice it. I see Jason acked that so I guess I will
just apply as is. Do you ack v6 too?
> > > }
> > >
> > > + virtnet_set_big_packets_fields(vi, mtu);
> > > +
> >
> > and here:
> > /* If device can receive guest GSO packets, allocate buffers for
> > * packets of maximum size, regardless of mtu.
> > */
> >
> > if (virtnet_check_guest_gso(vi)) {
> > vi->big_packets = true;
> > vi->big_packets_num_skbfrags = MAX_SKB_FRAGS;
> > }
> >
> >
> > > if (vi->any_header_sg)
> > > dev->needed_headroom = vi->hdr_len;
> > >
> > > --
> > > 2.31.1
[Date Prev] | [Thread Prev] | [Thread Next] | [Date Next] -- [Date Index] | [Thread Index] | [List Home]